Changeover Switch

Product Details:

07400015 Tesch F117x01 07400015 Safety Relay 24VAC/DC   opening and closure of the contacts. Emergency-Stop Relay F117 fulfils this requirement–EN954-1(3.97)– to the highest safety grade 4 as well. Protection against shorts in the F117 input circuit exists in case of applications involving a 2-channel emergency-stop

Product Details:

The rectangular inductive sensor IS5001 - IS-3002-BPOG from ifm operates with a supply voltage of 10-36 V DC. The output is a positive-switching NO contact. ifm electronic Inductive Block-Style Proximity Sensor

Product Details:

Phoniex Contact Make 5 PORT UNMANAGED ETHERNET SWITCH METAILIC BODY
Phoniex Contact Make 5 PORT UNMANAGED ETHERNET SWITCH METAILIC BODY

Additional Information:

• Delivery Time: Ex-stock

Product Details:

Safety relay for two hand device and many other safety products. Power supply 24VDC. Relay outputs 3NO/1NC ABB Jokab Safety Products ,JSBR4,JSBR3

Product Details:

Ethernet switch, 8 TP RJ45 ports, automatic detection of data transmission speed of 10/100 Mbps (RJ45), autocrossing function • RJ45 ports support a transmission speed of 10/100 Mbps • Local diagnostic indicators with LEDs • Auto negotiation and autocrossing detection simplifies installation and setup 

Product Details:

Elan Schmersal SRB-NA-R-C EW 24V 4 NO. 24VDC/VAC  Safety Controller 
 Input level. Single-channel control of the expansion module. SRB-NA-R-C.EW via one enabling output of the base.

Product Details:

• anufacturer: Elan
  Type: Safety Relay
  Model: SRB-NA-R-C-24V

  Rated Voltage: 24 VDC
  Rated Current: 120 mA
  Frequency: 50/60 Hz
  Contact Rating: 24 VDC, 6 A ; 230 VAC, 6 A
  Protection Class: IP20 / IP40
  Ambient Temperature: -25 … +45 °C
  Dimensions: 90 X 126.6 X 83 mm

Product Details:

The KL9010 bus end terminal is necessary for data exchange between the Bus Coupler and the Bus TerminThe KL9010 bus end terminal is necessary for data exchange between the Bus Coupler and the Bus Terminals. Each assembly must be terminated at the right hand end with a KL9010 bus end terminal. The bus end terminal does not have any other function or connection facility.als

Product Details:

SINUMERIK I/O MODULE PP 72/48 72 INPUTS 24 V 48 OUTPUTS 24 V I/O MODULE PP 72/48 WITH PROFIBUS 72 INPUTS 24 V 48 OUTPUTS 24 V, 0.25 A

Product Details:

Incremental, Resolution 360 P/R, 40 mm-dia., Shaft model, NPN open collector, Pre-wired models (0.5 m)Output short-cut protection Power supply reverse polarity protection Operating: -10 to 70 ℃ (with no icing) Storage: -25 to 85 ℃ (with no icing) Destruction: 10 to 500 Hz, 2-mm or 150 m/s² double amplitude for 11 min 3 times each in X, Y, and Z directions

Product Details:

• Precise linear 4...20 mA output signal
• High repeatability and low linearity error
• With long-term stability thanks to high overload protection
• Robust stainless steel housing for use in harsh industrial environments
• Wide operating temperature range

Product Details:

The IC200GBI001 Network Interface Module has 1024 points of discrete I/O memory, 128 bytes of analog I/O memory, and a 153.6 Kbaud network data rate. It interfaces a Versamax I/O station to a Genius I/O bus. The firmware version of the module is version 3.20. This firmware version can be downloaded to any hardware revision. Its enhanced diagnostic mode can be enabled for use in safety-relevant applications. The power consumption rating of the IC200GBI001 Module is 5 Volts at 250 milliamps or 3.3 Volts at 10 milliamps. The network data rate of the module is 153.6 Kbaud for both the extended and standard baud rate. It uses 3 rotary dials to configure its address and set the communication baud rate. It can be installed on a 35 x 7.5 millimeters conductive DIN rail. The module may be installed horizontally or vertically on the DIN rail. Make sure to remove the power supply before removing the module. 

Product Details:

• Three-way isolation: 1000 Vdc
• Accuracy: ±0.1% of full range
• Easy to configure input/output range
• Three VRs for calibrating accuracy of the input/ output range
• Flexible DIN-rail

Product Details:

PM100RL1A120 Mitsubishi Electric Gate Drivers IPM MODULE L1-SERIESThe PM100RL1A120 is a 1200V, 100A Intellimod intelligent power module. It is isolated base module designed for power switching applications operating at frequencies to 20KHz. Built in control circuits provide optimum gate drive and protection for the IGBT and free wheel diode power devices.

• 7-Pac circuit configuration
• Complete output power circuit
• Gate drive circuit
• Short circuit protection
• Overtemperature protection using on chip temperature sensing
• Undervoltage protection
• Low loss using full gate CSTBT IGBT chip

Product Details:

This product is part of the Modicon TM5 range, an offer of modules for IP20 modular I/O system. This terminal block offers 12 contacts.

Product Details:

PSS SB2 3006-3 ETH-2 COMPACT SAFETY SYSTEM WITH SAFETYBUS P CONNECTION 3rd generation compact safety system with SafetyBUS p and Ethernet interfaces. Suitable for safety-related functions because of its multi-channel diverse structure. 

Product Details:

EK1100 | EtherCAT Coupler
Beckhoff  The EK1100 EtherCAT Coupler is the link between the EtherCAT protocol at fieldbus level and the EtherCAT Terminals. The coupler converts the passing telegrams from Ethernet 100BASE-TX to E-bus signal representation. A station consists of a coupler and any number of EtherCAT Terminals that are automatically detected and individually displayed in the process image.

 

Additional Information:

• Production Capacity: 10
• Delivery Time: 2-4 days

Product Details:

Controlled phases: 3, Max. load [A]: 10, Coil voltage [V] DC [Min]: 5, Coil voltage [V] DC [Max]: 24

Controlled phases: 1, Max. load [A]: 15, Coil voltage [V] DC [Min]: 24, Coil voltage [V] DC [Max]: 230

Product Details:

PILZ-827225 - Single-phase voltage monitoring relay - measuring inputs are not polarity-sensitive - Pilz (PMDs S1UM) - S1UM 24Vdc UM 0.1-500Vac/DC UP Voltage monitoring relay, to monitor min. and max. voltage values, 12 measuring ranges 0.1 - 500 V AC/DC selectable, 0.40 -400 Hz, width = 22.5 mm, UB = 24 V DC, measuring inputs are notpolarity-sensitive.

Product Details:

IRIPRO Series offers a compact Over-current protection solution for distribution/feeder segment

Product Details:

Eurotherm PID used  a sensor to detect the Process Value (PV) such as a thermocouple or pressure sensing device. A controller to provide control of that process, referred to in the overhead as the term PID. An output to an actuator or device to control the input stimulus to that process, such as heat.

Product Details:

Hydrostatic submersible pressure transmitter PS4607

• Low-cost, simple level measurement
• Pressure compensation via internally vented cable
• Reduced wiring complexity when operated as two-wire current loop
• High overall accuracy and long-term stability
• Robust stainless steel housing with high ingress resistance

Product Details:

B&K PRECISION Make  DC Electronic Load 
Model No: 8540-105W DC

Additional Information:

• Delivery Time: 3-4 weeks

Product Details:

TLS-GD2 Guard Locking Switch is a positive-mode, tongue-operated interlock switch. It locks a machine guard closed until power is isolated then keeps the power isolated while the guard is open. The TLS-GD2 has three safety (N.C.) contacts and two auxiliary (N.O.) contacts.